Added to cart
Home / Chemicals / Carbon & Paint Removal / AlloySalt
ALLOY SYSTEM · Paint Stripper & DecarboniserTHIS PART: ALKALINE

Alloy SystemALLOYSalt-L — the alkaline part

Immersion & UltrasonicIMMERSION& ULTRASONICImmersion & UltrasonicSpray Wash CabinetSPRAY WASHCABINETSpray Wash Cabinet

The alkaline half of the Alloy System

ALLOYSalt-L — silicate alkaline liquid that lifts, emulsifies and suspends what the solvent loosens.

Non-flammable — safe in a heated ultrasonic bathSilicate alkaline liquid — the detergent halfEmulsifies oils, suspends paint residue for filtrationSystem-dosed with ALLOYSolv, never alone
From $410.00 ex GST
alloysalt container
PART · ALKALINEALLOYSalt-LSilicate alkaline liquid — lifts, emulsifies & suspends for filtration
+
PART · SOLVENTALLOYSolvBenzyl-alcohol solvent — penetrates & swells paint and carbon films
=
THE ALLOY SYSTEMSynergistic solvent + detergent action — paint and carbon off steel, cast iron, aluminium and zinc. MC-stripper performance, non-flammable at working temperature. Never on magnesium.
Why It Wins

The alkaline half of the Alloy System

A solvent that swells paint is only half a stripper — something must lift the loosened film, emulsify the oils underneath and keep the debris from redepositing on the work. ALLOYSalt-L is that half: a sodium-silicate alkaline liquid whose detergent action turns the solvent's work into a filterable result.

In the working bath the two parts run together at system ratio, and the division of labour is invisible — parts go in painted and carboned, come out bare, and the residue ends up in the filter bag instead of back on the metal.

Safe on steel, cast iron, aluminium and zinc — never magnesium. Sold as the Alloy System (both parts); this page covers the alkaline part for top-ups and system balance.

THE SOLVENT · ALLOYSolv

Penetrates and swells

Benzyl-alcohol solvent action gets under cured paint and carbonised films and swells them off the substrate — the job methylene chloride used to do, without its compliance burden.

THE ALKALINE · ALLOYSalt-L

Lifts, emulsifies, suspends

Silicate alkaline detergent lifts the loosened film, emulsifies the oils beneath, and holds residue in suspension so it ends up in the filter — not back on the work.

System Make-Up
ALLOYSolv (solvent)Matched volume with ALLOYSalt-L, as supplied in the system packs
ALLOYSalt-L (alkaline)Matched volume with ALLOYSolv, as supplied in the system packs
Dilution10% v/v of the mixed system in water (Kleentek TDS KT-TDS-ALSSYS)
Temperature40–70 °C — heating is required; ultrasonics or air agitation improves results markedly
Fire safetyThe mixed system is non-combustible per its SDS. ALLOYSolv on its own has a flash point of 101 °C — well above the working range; ALLOYSalt-L has none.
EquipmentUltrasonic tanks, agitated immersion, static tanks (agitate if possible), spray washers

Both parts dose into the same bath — one system, one make-up. The trial documents your working ratio, temperature and cycle before you commit.

Applications

Where it earns its keep

System additive boosting Alloysolve on cross-linked and stoved coatings.

AutomotiveRestoration
Material caution: Never on magnesium. Never dosed alone — system ratio with AlloySolve. AlloySalt is a Schedule 5 (Caution) poison; see the SDS.
Temperature & Dose
HEATING REQUIRED40–70 °C20 °C100 °C

Dose: 10% v/v of the mixed system in water, at 40–70 °C. The trial sets your exact process values; the TDS governs.

Run It Right

The working process

1 · MAKE UPMake upCombine both parts in matched volumes; 10% v/v of the mix in water.2 · HEATHeatBring to 40–70 °C, typically 56–65 °C — heating is required.3 · CLEANClean10–60 min, typically 30 min; filter the paint residues out.4 · RINSERinseRinse thoroughly with water before drying.
Buy the Alloy Systemex GST
Complete system
both parts · recommended
This part only
ALLOYSalt-L top-up
Alloy System · 10 L$410.00
Alloy System · 20 L$625.00
Alloy System · 200 L$5,450.00
Alloy System · 1,000 L$22,950.00
Includes ALLOYSolv (solvent) + ALLOYSalt-L (alkaline) — one system, one make-up.
$410.00

Delivered within Australia. Outside Australia, request a delivered price.

The Other Half — Required
ALLOYSolv · Solvent partBenzyl-alcohol solvent — penetrates & swells paint and carbon films
View Solvent part
Complete The Job
Anti-RustStops flash rust on cleaned steelView & buy →RegeniKThe ash stage after carbonView & buy →
Compatibility
Mild & carbon steelSteel on the TDS list
Stainless steelSafe in prescribed use
Cast ironCast iron on the TDS list
Aluminium & titaniumAluminium on the TDS list — the point of the system (titanium not listed; test)
Magnesium & soft alloysDo not use — not safe on magnesium
Zinc & galvanisedZinc on the TDS list — safe
Copper & brassNot on the TDS list — test first
Plated finishes (Cd·Cr·Ni)Not on the TDS list — confirm plating type first
Plastics & rubbersHDPE · PP · EPDM · Viton safe; acrylic, polycarbonate and ABS craze; nitrile seals swell — use EPDM or Viton
Painted / coated surfacesStrips paint — that is the job
Per prescribed use — the cleaning trial confirms on your parts; the TDS governs. Full range matrix →
Transport
TransportNot classified as Dangerous Goods for road and rail. AlloySalt is a Schedule 5 (Caution) poison
No DG freight surcharge applies.
Bath Life

This is not a single-use chemical

A common misconception treats industrial chemistry like dishwater — used once, tipped out. A defended bath of AlloySalt works for weeks of production: weir oil separation and filtration defend the bath, solids leave through the filter, and the chemistry keeps working until genuine depletion.

Change out on evidence, not anxiety: when cycle times stretch or results fade at correct concentration, the bath has earned its retirement. Top-ups at specification carry it between changes.

Keep It In Spec
  • Skim or weir oils continuously — oil load is bath killer #1
  • Filter solids; drain settled sludge from the sump
  • Verify concentration on schedule per the TDS check method
  • Log it — the trend predicts top-ups before cleaning fades
Storage

Drum and bath, both looked after

The Concentrate
  • Handling: Avoid eye contact and skin contact.
  • Avoid inhalation of vapour, mist or aerosols.
  • Storage: Store in a cool, dry, well-ventilated place and out of direct sunlight.
  • Store away from foodstuffs.
  • Store away from incompatible materials described in Section 10.
  • Store away from sources of heat and/or ignition.
  • Keep container standing upright.
  • Keep containers closed when not in use - check regularly for leaks.
  • This material is a Scheduled Poison Schedule 5 (Caution) and must be stored, maintained and used in accordance with the relevant regulations.
Compliant with the product SDS.
The Working Bath

Lid the tank between shifts — holds temperature, limits evaporation, keeps dust out.

Idle periods: a warm, stagnant aqueous bath can support biological growth over extended stagnation. Circulate periodically, keep concentration at specification, never leave an open tank standing for weeks.

Extended shutdown: drain to sealed, labelled containers — or schedule changeover for restart day.

Storage

Two drums, one discipline

Both Parts — From The SDS
LocationCool, dry, well-ventilated — out of direct sunlight
SegregationAway from foodstuffs, incompatible materials, and sources of heat or ignition
ContainersOriginal containers, sealed between uses — the solvent part loses strength to evaporation if left open
ALLOYSalt-L specificallyStore locked up (P405) — Poison Schedule S5, and its alkalinity demands segregation from acids
Shelf disciplineStore the two parts together as a system — a part that cannot find its partner is dead stock
The Working Bath

The made-up system is not a single-use fill. Between shifts, lid the tank: it limits evaporation of the solvent component, keeps airborne dust out, and holds temperature for a faster morning start.

Bath life is measured in work done, not days passed — emulsified oils skim off at the weir, paint residues collect in the filter, and the system chemistry keeps working until depletion, when a part-wise top-up (at system ratio) restores it.

For shutdown periods, drain and store made-up solution in sealed containers rather than leaving an open tank standing — and label the container with make-up date and ratio, because the next operator was not there when you mixed it.

Documents & Safety

The paperwork, on the page

Safety Data Sheets (SDS) — two-part system
The Alloy System runs as a pair — keep both Australian GHS SDSs in your chemical register.
ALLOYSolve PDF, 206 KBViewDownload
ALLOYSalt-L PDF, 211 KBViewDownload
Technical Data Sheet (TDS)
Alloy System TDS · KT-TDS-ALSSYS Rev 2 · 8 Sep 2026 covers AlloySolve and AlloySalt · PDF, 642 KBViewDownload
Hazard identification
DANGERPer Safe Work Australia GHS 7
Acute Toxicity - Oral - Category 4Irritation - Category 1BIrritation - Category 1
Hazard statements
H302Harmful if swallowed.
H314Causes severe skin burns and eye damage.
Key precautions
P102Keep out of reach of children.
P103Read carefully and follow all instructions.
P260Do not breathe dust, fume, gas, mist, vapours or spray.
P264Wash hands, face and all exposed skin thoroughly after handling.
P270Do not eat, drink or smoke when using this product.
P280Wear protective gloves/protective clothing including eye/face protection.
Compliant with the product SDS — full document available for your chemical register.
PPE & exposure controls
  • National occupational exposure limits: No value assigned for this specific material by Safe Work Australia.
  • Biological Limit Values: As per the "National Model Regulations for the Control of Workplace Hazardous Substances (Safe Work Australia)" the ingredients in this material do not have a Biological Limit Allocated.
  • Engineering Measures: Natural ventilation should be adequate under normal use conditions.
  • Personal Protection Equipment: SAFETY SHOES, OVERALLS, GLOVES, SAFETY GLASSES.
  • Personal protective equipment (PPE) must be suitable for the nature of the work and any hazard associated with the work as identified by the risk assessment conducted.
  • Product Name: Alloysalt Reference No: KT-CC-ALST Issued: 2021-06-30 Version: 1.1 Safety Data Sheet Wear safety shoes, overalls, gloves, safety glasses.
  • Available information suggests that gloves made from should be suitable for intermittent contact.
  • However, due to variations in glove construction and local conditions, the user should make a final assessment.
  • Always wash hands before smoking, eating, drinking or using the toilet.
  • Wash contaminated clothing and other protective equipment before storing or re-using.
Compliant with the product SDS — full document available for your chemical register.
First aid
  • If poisoning occurs, contact a doctor or Poisons Information Centre (Phone Australia 131 126, New Zealand 0800 764 766).
  • Inhalation: Remove victim from exposure - avoid becoming a casualty.
  • Remove contaminated clothing and loosen remaining clothing.
  • Allow patient to assume most comfortable position and keep warm.
  • Keep at rest until fully recovered.
  • Seek medical advice if effects persist.
  • Skin Contact: If skin or hair contact occurs, remove contaminated clothing and flush skin and hair with running water.
  • If swelling, redness, blistering or irritation occurs seek medical assistance.
  • For gross contamination, immediately drench with water and remove clothing.
  • Continue to flush skin and hair with plenty of water (and soap if material is insoluble).
Compliant with the product SDS — full document available for your chemical register.
Storage & handling
  • Handling: Avoid eye contact and skin contact.
  • Avoid inhalation of vapour, mist or aerosols.
  • Storage: Store in a cool, dry, well-ventilated place and out of direct sunlight.
  • Store away from foodstuffs.
  • Store away from incompatible materials described in Section 10.
  • Store away from sources of heat and/or ignition.
  • Keep container standing upright.
  • Keep containers closed when not in use - check regularly for leaks.
  • This material is a Scheduled Poison Schedule 5 (Caution) and must be stored, maintained and used in accordance with the relevant regulations.
Compliant with the product SDS — full document available for your chemical register.
Disposal
  • Persons conducting disposal, recycling or reclamation activities should ensure that appropriate personal protection equipment is used, see "Section 8.
  • Exposure Controls and Personal Protection" of this SDS.
  • If possible material and its container should be recycled.
  • If material or container cannot be recycled, dispose in accordance with local, regional, national and international Regulations.
Compliant with the product SDS — full document available for your chemical register.
Transport & dangerous goods
  • Product Name: Alloysalt Reference No: KT-CC-ALST Issued: 2021-06-30 Version: 1.1 Safety Data Sheet ROAD AND RAIL TRANSPORT Not classified as Dangerous Goods by the criteria of the "Australian Code for the Transport of Dangerous Goods by Road & Rail" and the "New Zealand NZS5433:
  • Transport of Dangerous Goods on Land".
  • MARINE TRANSPORT Not classified as Dangerous Goods by the criteria of the International Maritime Dangerous Goods Code (IMDG Code) for transport by sea.
  • AIR TRANSPORT Not classified as Dangerous Goods by the criteria of the International Air Transport Association (IATA) Dangerous Goods Regulations for transport by air.
Compliant with the product SDS — full document available for your chemical register.
AlloySalt FAQ

Asked at the tank

What dilution and temperature do I run?
10% v/v of the mixed system in water at 40–70 °C, typically 56–65 °C, for 10–60 minutes (typically 30) — and the trial sets your exact process values against your soil. Running richer than specified wastes chemical without cleaning faster. That range is the chemistry’s window — not the whole answer. The substrate sets its own ceiling, and it is usually lower: aluminium and anodised finishes discolour above about 65 °C, zinc and coated parts lower again, and magnesium is governed by pH before temperature. Run at the lower of the two. Bath temperature — chemistry vs substrate →
When do I change the bath?
When cycle times stretch, results fade, or filtration stops holding the debris. Drain, clean the tank, refill — never lay fresh solution over settled sludge.
Can algae grow in the bath if it sits unused?
Over extended stagnation, any warm diluted aqueous bath can support growth as preservative systems deplete. Prevention: circulate periodically, hold concentration at specification, lid the tank. If a bloom happens: drain, clean the tank including weir and lines with hot fresh solution, rinse and refill — never dose on top of growth.
Can I get the SDS before buying?
Yes — every product ships with its SDS, and documents are available ahead of purchase for your chemical register and risk assessments.

Prove it on your parts

The trial pairs AlloySalt with your components — concentration, temperature and cycle documented before you order a drum. Wrong chemistry for your soil? The trial says so.

Talk to an engineer Back to the Range
Goes with this

Filter bags for this bath

The bag is what keeps the bath working — it takes the soil out before it settles back onto the next load. Which media suits this one depends on its pH, so ask us before you order.

ask firstTell us the bathpH not yet published

The bag media is settled by the pH, and we have not published one for this product yet. Ask us and we will tell you which felt to run.

Size 17″ × 16″housing 717Size 27″ × 32″housing 732Size 34″ × 8″housing 408Size 44″ × 14″housing 415
Which size, media and micron — the full guide →
Payment is processed by Stripe; we do not see your card number. We use your details to process and deliver the order, as our Privacy Policy describes.