Ultrasonic Cleaners and Parts Washers for Perth and WA
A haul truck engine comes down in the Pilbara and the injectors, the turbo hardware and the valve blocks all have to be clean before anything goes back together. In most WA workshops that means a solvent drum, a brush and a bench, or a pallet of parts freighted east and waited on.
Misonics puts the cleaning capability inside your own workshop — the machine, the chemistry, and a process card written for your parts — so components stop leaving site to get clean. Ultrasonic tanks and sealed parts washers, from benchtop units that run off a standard 10 A socket up to tanks that take a heat exchanger bundle.
What comes off on a WA site
Diesel injectors and fuel system parts
Carbon at the nozzle tip and lacquer through the body, in bores too small to take a brush. Cavitation reaches the bore because the liquid does.
Turbocharger components
Oil coke on the turbine side, soot through the housing, and carbon packed into variable geometry vanes and their linkages.
Hydraulic valve blocks and spools
Varnish and fine metallic debris out of drillings, seats and spool bores, with the block cleaned whole rather than stripped.
Heat exchanger and radiator cores
Scale, oil and red dust packed into the tube stack, cleaned through the core without rodding it.
Final drive and transmission parts
Gear oil, friction material and dust baked onto housings, hubs and planetary components.
Filter elements
Pleated stainless mesh elements recovered and put back into service instead of replaced. See the case study.
Getting a machine onto a WA site
Power
The benchtop machines run on 240 V, 50 Hz single phase from a standard 10 A socket on a 3 m lead. Floor-standing MSX units carry that up the range, so a workshop gets floor-scale cleaning without a switchboard project. The large tanks and the multi-stage systems need 415 V three phase.
Water and waste
A tank is filled once and runs for weeks on the same charge with filtration on it. At the end of its life it is a waste stream you will need a plan for, and we will tell you what is in it before you buy rather than after.
Freight
Benchtop and floor-standing machines travel on a pallet as general freight to Perth and on to site. Large tanks travel oversize. Freight and lead time are quoted as their own lines so you can see what the transport costs.
Chemistry resupply
Concentrate ships in 20 and 200 litre drums. Dose rates are on the technical data sheet, so you can work out a year of consumption before you commit and hold stock to suit the run.
Commissioning
Quoted against the machine and the site. The machine is filled, run and load-tested before it leaves us, so what arrives has already worked.
Support afterwards
Process and settings by phone and remote session, with a technician on site where the job needs one. Spares and consumables freight from Australian stock, and the process card stays with the machine so a new hand can run it.
Keeping it running in WA
What distance costs
A technician to a Pilbara site is two days of travel before anyone opens a panel. That figure decides whether a machine gets repaired or gets worked around.
Remote access, custom builds
Custom builds ship with Ewon Cosy 131 remote access as standard — a secure connection into the machine’s controller. We work on the live machine while it runs, without attending site.
A control module that travels
MSX 50 to 240 carry a demountable control module. It unplugs and travels by courier; the tank stays on your floor. Software loads over a direct computer connection on site.
The machine follows the site
PowerSonic
Benchtop for injectors, nozzles and small assemblies on the workshop bench. See the range.
MSX
Floor-standing, built in Australia, single phase well up the range. See the range.
UltraWash
A sealed multi-stage parts washer, for parts that have to come out clean, rinsed and dry in one door. See the range.
What are you cleaning, and where is it?
Tell us what the part is, what comes off it, and what the workshop has for power, water and drainage. Technical sales will tell you whether ultrasonics is the right answer for that part and what it takes to run it on your own floor.
Questions we get from Western Australia
Where can I get an industrial ultrasonic cleaner in Perth?
Direct from us. We supply Perth and the whole of WA, freighted to site. The machine is specified against the part before anything is quoted.
What is the difference between these and the cheap ones online?
Duty cycle, transducer construction, tank gauge, and whether anyone answers when it fails. Bench size is not the dividing line — the MSX 15 and MSX 30 sit on a workshop bench and are built for shift work.
Will it clean injectors, turbo hardware and valve blocks?
Yes. That is most of what WA sites run them for. Chemistry is selected for the soil and the substrate, not sold as one bottle for everything.
Can it clean a DPF?
Yes, with the right machine and cycle.
How long does it take to get a machine to a WA site?
It depends on the machine. A small machine held in stock goes straight out. Anything larger is custom made, or assembled in our workshop before it ships. Remote destinations add transit, and we state it up front.
Who services it once it is out there?
Us, mostly without freighting it. Custom builds are diagnosed live through Ewon Cosy 131 remote access. On the MSX 50 to 240 the control module comes out on its own and travels by courier, so the tank stays on your floor. Spares are held in Australia.