Added to cart
Home / Chemicals / Degreasing & General Cleaning / AquaVantage 1990 GD
Brulin Engineered

AquaVantage 1990 GD

Spray Wash CabinetSPRAY WASHCABINETSpray Wash Cabinet

High performance for the precision end

Brulin's advanced GD-series chemistry for aerospace and OEM duties.

Advanced GD-series performanceAerospace & OEM precision dutiesGrade-matched to your specification in trial
From $220.00 ex GST
brulin aquavantage 1990 gd container

Four AquaVantage grades. Same substrate safety across all of them — the difference is the duty.

815 GDNew manufacture — cutting oils, coolants, lapping and buffing pastes, fluxesView →815 QR-NFMRO and rebuild — service carbon, baked greases, operating soilsView →1990 GDSpray cabinets and rotary basket washers, as well as tanksYou are here1696 GDNear-neutral — sensitive substrates and mixed-metal assembliesView →
One bath, three jobs

Degrease, free rinse, corrosion inhibitor

AquaVantage 1990 GD does three jobs in one bath, so a part can come out of the machine ready for the next operation instead of going through three tanks to get there.

1

Degrease

Lifts buffing compounds, coolants, fats, greases and the whole run of oils — cutting, drawing, forming, hydrocarbon, lubricants, water-soluble. Released oil separates out for skimming instead of emulsifying into the bath, so the tank lasts.

Data sheet: separates oil effectively for improved oil removal
2

Free rinse

The surfactant and builder package is picked so it goes back into solution in the rinse water and sheets off the part, instead of beading up or drying to a film. That sheeting is what a water-break-free surface is.

It matters because of what comes next. Anything left on the surface is an adhesion defect in the paint, the bond, the plate or the coating, and it will not show up until that stage fails.

Data sheet: free rinsing — permits improved adhesion
3

Corrosion inhibitor

Two different jobs, and it is worth keeping them apart. In the tank: the bath is alkaline, so steel sits in its passive range and holds a stable oxide, and the inhibitor package adsorbs a film on the surface. None of that follows the part out of the bath.

Out of the tank: a trace carries through the rinse and holds off flash rust for a short while — indoors and dry. It is a residual film, not a coating. For anything going on a shelf, follow it with a dedicated rust preventative.

Data sheet: in-process corrosion control

Getting the protection to survive the rinse

This is where most people lose it. A freshly cleaned part is the worst case there is — you have just taken off the oil film that was protecting it, and bare steel sitting wet in aerated water goes off in minutes. Four things decide whether it holds.

Rinse hot, 60–70 °CParts come out carrying enough heat to flash themselves dry. One change, and it fixes more flash rust than anything else on this list.
Dry straight awayForced air or vacuum. Do not let parts drip-dry on a bench — time sitting wet is the single biggest lever there is.
Wet between, dry afterKeep parts wet from stage to stage so they do not spot, then get them properly dry after the last one. Wet-to-wet is fine; wet-to-air rusts.
Do not over-rinseEvery extra litre takes more inhibitor off. Match the rinse to the spec: under 50 µS/cm for ultra-clean, under 500 for precision. Long hot cascades and DI strip it fastest.

Three tanks become one. Less floor space, one bath to dose and monitor, one drum to buy, and no transfer between stages for the part to flash over in. Dose and temperature are on the dosage calculator →

Why It Wins

High performance for the precision end

The GD series exists on a spectrum, and 1990 GD occupies the high-performance end: advanced aqueous cleaning for precision aerospace and OEM work, with the free-rinsing, oil-splitting behaviour the series is qualified on.

Its brand documentation is on file and its slot in the range is specification-driven — where 815 GD is the qualified default, 1990 GD answers the applications that ask for more, confirmed per specification in trial.

Talk to us with the spec in hand; matching the GD grade to the requirement is exactly the kind of decision the trial exists to settle.

Applications

Where it earns its keep

Precision aerospace cleaning duties across OEM and MRO work.

AerospaceDefenceManufacturing
Material caution: Spray-wash detergent — very low foaming above 49 °C, built for cabinet and inline washers. Keep at least 5% when cleaning aluminium. Zinc, tin and soft solder are not on the approved list.
Temperature & Dose
SWEET SPOT 60 °C49–77 °C20 °C100 °C

Dose: 3–15% (typ. 5%; 5% minimum on aluminium). The trial sets your exact process values; the TDS governs.

Run It Right

The working process

1 · MAKE UPMake upConcentrate at 3–15% (typ. 5%) in water; at least 5% when cleaning aluminium.2 · HEATHeatBring to 49–77 °C (typically 54–66 °C); low-foaming above 49 °C.3 · CLEANCleanSpray wash, batch or continuous; typical parts clean in 3–10 min.4 · RINSERinseWater rinse; heated where finish matters. Keep parts wet between stages.
The GD Family

Right product, right job

This Page

1990 — high performance

Specification-driven precision duties.

Also Consider

AquaVantage 815 GD

The qualified default

View →
Buy AquaVantage 1990 GDex GST
10 L$220.00
20 L$415.00
200 L$3,900.00
1,000 L$14,790.00

Delivered within Australia. Outside Australia, request a delivered price.

Complete The Job
Anti-RustStops flash rust on cleaned steelView & buy →
Compatibility
Mild & carbon steelSafe in prescribed use
Stainless steelSafe in prescribed use
Cast ironSafe in prescribed use
Aluminium & titaniumAerospace-approved multi-metal duty — aluminium and titanium on the TDS list
Magnesium & soft alloysMagnesium and its alloys on the TDS list
Zinc & galvanisedNot on the TDS list — test first
Copper & brassCopper alloys and plating on the TDS list
Plated finishes (Cd·Cr·Ni)Cadmium, chrome and nickel plating all on the TDS list
Plastics & rubbersAcrylics · HDPE · nitrile · PVC · rubber on the TDS list
Painted / coated surfacesPainted surfaces on the TDS list
Per prescribed use — the cleaning trial confirms on your parts; the TDS governs. Full range matrix →
Transport
TransportNot classified as Dangerous Goods for transport
Bath Life

This is not a single-use chemical

A common misconception treats industrial chemistry like dishwater — used once, tipped out. A defended bath of AquaVantage 1990 GD works for weeks of production: the oil-splitting formulation sends released oils to the weir, solids leave through the filter, and the chemistry keeps working until genuine depletion.

Change out on evidence, not anxiety: when cycle times stretch or results fade at correct concentration, the bath has earned its retirement. Top-ups at specification carry it between changes.

Keep It In Spec
  • Skim or weir oils continuously — oil load is bath killer #1
  • Filter solids; drain settled sludge from the sump
  • Verify concentration on schedule — titration method on the product TDS
  • Log it — the trend predicts top-ups before cleaning fades
Storage

Drum and bath, both looked after

The Concentrate
  • Precautions for safe handling Before use carefully read the product label.
  • Use of safe work practices are recommended to avoid eye or skin contact and inhalation.
  • Observe good personal hygiene, including washing hands before eating.
  • Prohibit eating, drinking and smoking in contaminated areas. 7.2 Conditions for safe storage, including any incompatibilities Store in a cool, dry, well ventilated area, removed from incompatible substances and foodstuffs.
  • Ensure containers are adequately labelled, protected from physical damage and sealed when not in use.
  • Check regularly for leaks or spills. 7.3 Specific end uses No information provided.
Compliant with the product SDS.
The Working Bath

Lid the tank between shifts — holds temperature, limits evaporation, keeps dust out.

Idle periods: a warm, stagnant aqueous bath can support biological growth over extended stagnation. Circulate periodically, keep concentration at specification, never leave an open tank standing for weeks.

Extended shutdown: drain to sealed, labelled containers — or schedule changeover for restart day.

On the drum

The icons on the label, and what they mean

ConcentrateSupplied concentrated. Dilute before use.
All MetalsMarked for use across ferrous and non-ferrous metals.
AerospaceMarked for aerospace work. Named approvals are listed under Compliance.

These are the manufacturer’s own label marks, not third-party certifications. Where a named approval exists it is listed in full on this page. The compatibility table above is what governs.

Documents & Safety

The paperwork, on the page

Safety Data Sheet (SDS)
AquaVantage 1990 GD — Australian GHS SDS for your chemical register and risk assessments. PDF, 158 KB. Issued 01/07/2026.
View SDSDownload
Technical Data Sheet (TDS)
Kleentek KT-TDS-AV1990GD · Rev 2 · issued 10 Sep 2026. Dose, temperature, material compatibility, soils, bath control and transport — replaces the Brulin sheet. PDF, 239 KB.
View TDSDownload
Hazard identification
WARNINGPer Safe Work Australia GHS 7
Hazard statements
H315Causes skin irritation.
H319Causes serious eye irritation.
Key precautions
P264Wash thoroughly after handling.
P280Wear protective gloves/protective clothing/eye protection/face protection.
P352IF ON SKIN: Wash with plenty of soap and water.
P338IF IN EYES: Rinse cautiously with water for several minutes.
P321Specific treatment is advised - see first aid instructions.
P313If skin or eye irritation occurs: Get medical advice/ attention.
Compliant with the product SDS — full document available for your chemical register.
PPE & exposure controls
  • Control parameters Exposure standards No exposure standards have been entered for this product.
  • Biological limits No biological limit values have been entered for this product. 8.2 Exposure controls Engineering controls Avoid inhalation.
  • Use in well ventilated areas.
  • PPE Eye / Face Wear splash-proof goggles.
  • Hands Wear PVC or rubber gloves.
  • Body When using large quantities or where heavy contamination is likely, wear coveralls.
  • Respiratory Not required under normal conditions of use.
Compliant with the product SDS — full document available for your chemical register.
First aid
  • Description of first aid measures Eye If in eyes, hold eyelids apart and flush continuously with running water.
  • Continue flushing until advised to stop by a Poisons Information Centre, a doctor, or for at least 15 minutes.
  • Inhalation If inhaled, remove from contaminated area.
  • Apply artificial respiration if not breathing.
  • Skin If skin or hair contact occurs, remove contaminated clothing and flush skin and hair with running water.
  • Continue flushing with water until advised to stop by a Poisons Information Centre or a doctor.
  • Ingestion For advice, contact a Poisons Information Centre on 13 11 26 (Australia Wide) or a doctor (at once).
  • If swallowed, do not induce vomiting.
  • First aid facilities Eye wash facilities and normal washroom facilities should be available. 4.2 Most important symptoms and effects, both acute and delayed May cause irritation to the eyes, skin and respiratory system. 4.3 Immediate medical attention and special treatment needed Treat symptomatically.
Compliant with the product SDS — full document available for your chemical register.
Storage & handling
  • Precautions for safe handling Before use carefully read the product label.
  • Use of safe work practices are recommended to avoid eye or skin contact and inhalation.
  • Observe good personal hygiene, including washing hands before eating.
  • Prohibit eating, drinking and smoking in contaminated areas. 7.2 Conditions for safe storage, including any incompatibilities Store in a cool, dry, well ventilated area, removed from incompatible substances and foodstuffs.
  • Ensure containers are adequately labelled, protected from physical damage and sealed when not in use.
  • Check regularly for leaks or spills. 7.3 Specific end uses No information provided.
Compliant with the product SDS — full document available for your chemical register.
Disposal
  • Waste treatment methods Waste disposal Reuse where possible.
  • For small amounts, flush to sewer with excess water.
  • Alternatively absorb with sand, vermiculite or similar and dispose of to an approved landfill site.
  • Contact the manufacturer/supplier for additional information if disposing of large quantities (if required).
  • Legislation Dispose of in accordance with relevant local legislation.
Compliant with the product SDS — full document available for your chemical register.
Transport & dangerous goods
  • INFORMATION NOT CLASSIFIED AS A DANGEROUS GOOD BY THE CRITERIA OF THE ADG CODE, IMDG OR IATA LAND TRANSPORT (ADG) SEA TRANSPORT (IMDG / IMO) AIR TRANSPORT (IATA / ICAO) 14.1 UN Number None allocated.
  • None allocated. 14.2 Proper None allocated.
  • Shipping Name 14.3 Transport None allocated.
  • None allocated. hazard class 14.4 Packing Group None allocated.
  • None allocated. 14.5 Environmental hazards Not a Marine Pollutant. 14.6 Special precautions for user Hazchem code None allocated.
Compliant with the product SDS — full document available for your chemical register.
AquaVantage 1990 GD FAQ

Asked at the tank

What dilution and temperature do I run?
3–15% (typ. 5%) at 49–77 °C, typically 54–66 °C, for 3–10 minutes — and the trial sets your exact process values against your soil. Running richer than specified wastes chemical without cleaning faster. That range is the chemistry’s window — not the whole answer. The substrate sets its own ceiling, and it is usually lower: aluminium and anodised finishes discolour above about 65 °C, zinc and coated parts lower again, and magnesium is governed by pH before temperature. Run at the lower of the two. Bath temperature — chemistry vs substrate →
When do I change the bath?
When cycle times stretch, results fade, or filtration stops holding the debris. Drain, clean the tank, refill — never lay fresh solution over settled sludge.
Can algae grow in the bath if it sits unused?
Over extended stagnation, any warm diluted aqueous bath can support growth as preservative systems deplete. Prevention: circulate periodically, hold concentration at specification, lid the tank. If a bloom happens: drain, clean the tank including weir and lines with hot fresh solution, rinse and refill — never dose on top of growth.
Can I get the SDS before buying?
Yes — every product ships with its SDS, and documents are available ahead of purchase for your chemical register and risk assessments.

Prove it on your parts

The trial pairs AquaVantage 1990 GD with your components — concentration, temperature and cycle documented before you order a drum. Wrong chemistry for your soil? The trial says so.

Talk to an engineer Back to the Range
Compliance, Standards & Conformance

Approved and conformant — by name

AquaVantage 1990 GD carries one of the broadest approval sets in the Brulin range. If your process is governed by one of these specifications, the chemistry is already qualified for it.

Airframes
  • Airbus AIPI 09-01-003
  • Airbus UK ABP 8-1290
  • Boeing BAC 5763 Emulsion Cleaning
  • Boeing HP 9-25 Degreasing
  • Boeing D6-17487 Rev. K Exterior Cleaner
  • Teledyne Ryan RACO 2833
Engines
  • Rolls-Royce CSS204 Type A
  • Rolls-Royce OMAT 1/24 AG
  • Safran PR-1500 · DMP 13-300
  • GE Aviation S-421
  • GE Aviation CT-882 Solvent Replacement
  • Lucas Aerospace DC Starter/Gen
Space, Defence & Industry
  • NASA — Cleaning for Oxygen Service
  • Lockheed Martin EPS G32.0160 · LMA-PG006
  • General Dynamics (Electric Boat)
  • UTC Aerospace (Rohr) ML21345
  • Honeywell EMS 53170 · Meggitt AP-842
  • USDA A1 · SCAQMD Clean Air Solvent
Test Compliance
  • ARP 1755A (Cat. 9) · 1755B (Cat. 10)
  • ASTM F-483 · F-484 · F-485 · F-502
  • ASTM F-519 Hydrogen Embrittlement
  • ASTM F-945 Ti Stress · F-1110 · F-1111
  • NSN 6850-01-428-8842 · 6850-01-435-6459
  • No cyanides · No sulfides

Source: Brulin Specification Conformance & Testing (750-042Z). Approvals are held by the manufacturer and apply to the product as supplied — confirm the current revision with Misonics before writing it into a process specification.

Goes with this

Filter bags for this bath

The bag is what keeps the bath working — it takes the soil out before it settles back onto the next load. This is a strong alkaline bath, and that rules the media in and out before micron rating comes into it.

what we would sendPolypropylene needlefeltStrong alkaline bath · pH above 11 · caustic

Rated to pH 14. This is what it is for. Start at 25 µm unless something downstream needs finer.

Not polyester or nylon. Caustic hydrolyses polyester — the ester bond is cleaved and the bag loses strength until it tears. Heat makes it fast. Use polypropylene. Nylon is rated pH 3–11. Above 11 it is out of spec.
Size 17″ × 16″housing 717Size 27″ × 32″housing 732Size 34″ × 8″housing 408Size 44″ × 14″housing 415
Which size, media and micron — the full guide →
Payment is processed by Stripe; we do not see your card number. We use your details to process and deliver the order, as our Privacy Policy describes.